If you have a residential or commercial garage door opener, here are a few quick tips to repair the most common garage door opener issues.
First, check to ensure the power is turned on and the door opener is plugged into an outlet.,
check to make sure that the power is turned on and that the door opener is plugged into an outlet. If it is, then check to see if the door opener itself is working by pressing the button on the unit. If it does not work, then you may need to replace the batteries.
If the door opener still does not work, you will need to open up the unit to check the wiring. Unplug the door opener from the power outlet. Then, remove the cover of the unit to access the wiring. Once you have access to the wiring, check to see if there are any loose or damaged wires. If you find any, then you will need to repair or replace them.
BE CAREFUL ( Do not unplug or plug to any source of power or any of the wires and just visually inspect the opener. It could be harmful and cause an electronic shock if you did any wrong wiring or even touched an uncovered part of the Opener ).
Once you have checked the wiring, replace the cover of the unit and plug it back into the power outlet. Press the button on the unit to see if it is now working. If it is, then you have successfully repaired your commercial door opener. if still, your opener didn’t work you should call an expert worker.
We can do the work for you Call Us at (305) 702-0113 We serve in Miami Dade & Broward County Florida.
Common Garage Door Opener Issues
Garage door repair is a process that is relatively straightforward, however, there are a few things that you need to check that would make the entire process smoother. We have listed some of the common issues that you may face, and how you can solve them.
1- Wall button not working
it’s common for the wall button to not work after a while due to a malfunction in the electrical circuit or circuit breaker, don’t worry wall button is replaceable and it is easy to install so if you found your wall button is not responding or not powering up so it’s probably the problem is from your wall button and not your opener itself.
2- The opener doesn’t stop running after your garage door is completely open
If your garage door opener doesn’t stop running after your garage door is completely open, there are a few possible causes. First, check to see if the travel limit switch needs to be adjusted. This switch tells the opener when to stop running, so if it’s not properly adjusted, the opener will keep running.
Second, check the force setting. This setting determines how much force is required to open the door, and if it’s set too low, the opener will keep running. Finally, check the garage door itself to make sure it’s not binding on the tracks. If the door is binding, the opener will keep running in an attempt to open the door.
You May Like: Basic Garage Door Maintenance Recommendations
But in general, there are two main signs that the limit switch needs adjustment first
- Your garage door is not opening or closing fully.
- Your garage door reverses itself after reaching the ground.
if you are experiencing one of these signs and at the same time the opener doesn’t stop running after your garage door is completely open that properly means you need to adjust the limit switch.
3- Your garage door reverses itself after reaching the ground
One of the most common problems is when you are closing your garage door even open it reverses back. this problem could be because of many reasons
- The threshold May Be Blocked
The garage door may not be opening because there is something blocking the threshold. This can be things like leaves, snow, or other materials. If the garage door is obstructed by a threshold, it could make the travel-down setting higher or lower than the setting it already saved.
- Travel Down Setting Needs to be Adjusted
If your garage door is traveling down too far, it’s likely that the travel-down setting needs to be adjusted. This setting controls how far the door will travel down when it’s opened. To adjust it, you’ll need to find the travel-down adjustment on the opener. It’s usually located on the back of the opener, near the bottom. Once you’ve found it, turn it clockwise to decrease the travel distance, or counterclockwise to increase it.
- Your Keypad Enter button is sticky
Believe it or not, it is simple like that because if your keypad buttons are sticky, especially the enter button stuck could result in making your door keep closing after you put your passkey.
0 Comments